Flaring & Expanding Tools

Find the right HVAC Flaring Tool for clean, leak-free flare joints on refrigeration and air conditioning installs, along with tube expanders for fast, fitting-free brazed joints. A good flare is one of the most important connections on a split system, and the right tool makes it repeatable every time.

Choose from eccentric and ratchet flaring tools with clutch cut-offs that stop you over-flaring, R410A-type tools for higher-pressure systems, and Cordless Electric Flaring Tools that cut the effort and time on busy install days. For brazed connections, a Tube Expander Kit swages the end of one tube so another of the same size slides straight in, removing the need for a coupling and reducing the number of joints in the system.

Filter and sort 17 products
Sort by
If you can't see what you need, we can help you.

Flaring Tools and Tube Expanders Explained

Flaring and expanding are two ways of preparing copper tube for a connection. A flaring tool forms a 45° cone on the end of the tube, which seals against the fitting when the flare nut is tightened. Flare joints are standard on split system indoor and outdoor unit connections because they can be made and remade without brazing. A tube expander, also called a swaging tool, enlarges the end of a tube so another tube of the same size fits inside it, ready for brazing. That removes the need for a coupling, which means one joint instead of two. Expanders come as lever kits with interchangeable heads, compact hand-held tools, hydraulic kits for larger tube, and simple swaging punches. Both tool types sit at the core of any installer's hvac hand tools.

Choosing an HVAC Flaring Tool

Eccentric flaring tools are the most common choice today. The cone rolls around the inside of the tube rather than forcing straight in, which burnishes a smooth, even flare, and many include a clutch or torque cut-off that stops automatically once the flare is complete. Ratchet models reduce the effort further in tight spaces. If you work on R410A or R32 systems, choose an R410A-type tool, as these are built for the flare dimensions used on higher-pressure refrigerants. For high-volume installers, an electric flaring tool or battery flaring tool produces consistent flares in seconds with almost no hand effort, which reduces fatigue and variation between flares across a long day. Kits that add a tube cutter and deburrer are a practical starting point for apprentices.

Getting Leak-Free Flares and Swages

Most leaking flares start with poor tube preparation. Cut the tube square with a sharp pipe cutter, then deburr the inside edge lightly without thinning the wall, and keep the tube pointing down so filings fall out rather than into the pipe. Always slide the flare nut onto the tube before flaring. Set the tube height in the flaring bar using the tool's gauge, as too little tube gives a small flare and too much can split it. Lubricate the cone as the tool manufacturer recommends, then inspect the finished flare: it should be smooth, even and free of cracks. Tighten flare nuts with a torque wrench to the equipment maker's specification. Shape the line set with a copper pipe bender rather than extra fittings to keep joints to a minimum.


FAQ of Flaring & Expanding Tools

What is the best HVAC flaring tool for split system installs?

For most installers, an eccentric flaring tool with a clutch or torque cut-off is the best all-round choice. It produces smooth, consistent flares and stops automatically to prevent over-flaring. Choose an R410A-type model if you work on R410A or R32 systems. High-volume installers often add a cordless electric flaring tool to save time and reduce hand fatigue.

Is an electric flaring tool worth it?

If you make a lot of flares, usually yes. An electric or cordless flaring tool forms a flare in seconds with little hand effort, and because the motor does the work, flares are more consistent from one connection to the next. For occasional use, a quality manual eccentric tool does the same job at a lower cost. Many installers keep a manual tool as a backup.

Do I need an R410A flaring tool for R32 systems?

R32 and R410A both operate at higher pressures than older refrigerants, and their equipment typically uses the flare dimensions that R410A-type flaring tools are designed for. Using an R410A-type tool helps ensure the flare matches the flare nut and seats correctly. Always check the equipment manufacturer's installation manual for the required flare dimensions and tightening torque.

What is a tube expander used for?

A tube expander, or swaging tool, enlarges the end of a copper tube so another tube of the same diameter slides inside it. The joint is then brazed. This replaces a coupling, so you make one brazed joint instead of two, which saves time and reduces potential leak points. Lever expander kits with interchangeable heads cover the most common tube sizes.

Why do my flares crack or leak?

The most common causes are a tube end that isn't cut square, burrs left inside the tube, setting too much tube above the flaring bar, or over-tightening the flare nut. Hard or work-hardened copper can also crack. Cut cleanly, deburr carefully, use the tool's height gauge, and tighten to the specified torque with a torque wrench.