Benders & Straighteners

Our Copper Pipe Bender range helps HVAC/R technicians and installers make clean, kink-free bends in soft copper tube, from small refrigerant lines to larger line sets. Bending the pipe instead of adding elbows means fewer brazed joints, fewer potential leak points and a neater, faster install.

Choose a Spring Bender for quick, gentle bends in soft coil, a lever Tube Bender for accurate 90° and 180° bends with degree markings, or a ratchet Pipe Bender for larger tube with less hand effort. Multi-size and kit options let you cover common imperial sizes with one tool, so you can match every line on the job without carrying a full set of single benders.

Filter and sort 22 products
Sort by
If you can't see what you need, we can help you.

Types of Pipe and Tube Benders

Spring benders slide over the outside of soft copper tube and support the wall as you bend by hand, which stops the pipe flattening or kinking. They're quick, light and ideal for gentle bends, but they rely on your hands to control the radius and angle. Lever tube benders use a fixed former and a handle to wrap the tube around a set radius, with degree markings for accurate, repeatable 45°, 90° and 180° bends. Multi-size lever benders combine several formers in one tool, saving space in the toolbag. Ratchet and crossbow-style benders use mechanical advantage to bend larger tube with less effort, making them the better choice for bigger line sets and long days on the tools.

Choosing a Copper Pipe Bender

Start with the tube size. Benders are sized by the outside diameter of the copper, and refrigeration tube in Australia is usually specified in imperial sizes such as 1/4", 3/8", 1/2" and 5/8", so match the former to the pipe exactly. A bender that is too large won't support the tube wall, and one that is too small won't fit. Next, consider how often you bend: an apprentice or occasional installer may only need a spring bender set or a multi-size lever bender, while a busy installer working on larger line sets will save time and effort with a ratchet bender. Finally, check that the tool is designed for annealed (soft) copper, as hard-drawn tube needs to be annealed before bending. Pair your bender with the rest of your hvac hand tools to cover every step of the pipework.

Tips for Kink-Free Bends

Straighten coiled tube before you bend, so the bend starts from a true line and finishes at the angle you marked. Measure and mark the tube, line the mark up with the zero on the bender's former, and apply steady, even pressure rather than forcing the bend in one movement. Copper springs back slightly, so bend just past your target angle and check it. Keep the tube clean and capped to stop dirt and moisture entering the system. After bending, cut the tube square with a [link: pipe cutter], deburr it, and finish the joint with a quality hvac flaring tool. Wipe your bender clean after each job and check the former for burrs or damage, as a nicked former can mark or crush the tube.


FAQ of Benders & Straighteners

What is the best copper pipe bender for split system installs?

For most split system work, a lever tube bender in each common size, or a multi-size lever bender, gives the most accurate results, as the former controls the radius and the markings show the angle. Spring benders are a cheap, light backup for gentle bends. If you regularly bend larger line sets, a ratchet bender reduces the effort needed.

What's the difference between a spring bender and a lever tube bender?

A spring bender is a coiled sleeve that fits over the tube and supports its wall while you bend by hand. It's quick and portable but less precise. A lever tube bender wraps the tube around a fixed former, giving a consistent radius and accurate angles marked on the tool. Many technicians carry both: a lever bender for precise bends, a spring bender for quick adjustments.

Can you bend hard-drawn copper pipe?

Hard-drawn copper is too stiff to bend cleanly and is likely to crack or kink. Most bending tools are designed for annealed (soft) copper, which is the type normally supplied in coils for refrigeration and air conditioning work. If you need to bend hard-drawn tube, it must first be annealed by heating it evenly and letting it cool, or you can use fittings instead.

How do I stop copper pipe kinking when bending?

Use a bender that matches the tube's outside diameter exactly, so the wall is fully supported. Straighten the tube first, bend slowly with steady pressure, and never try to bend tighter than the former's radius. Make sure you're bending soft (annealed) copper, not hard-drawn tube. If a bend does kink, cut it out, as a kink restricts flow and weakens the pipe.

What size tube bender do I need?

Choose the bender size by the outside diameter (OD) of the copper tube, not the inside diameter. Refrigeration and air conditioning tube in Australia is usually sized in inches, with 1/4", 3/8", 1/2" and 5/8" common on split system line sets. If you work across several sizes, a multi-size bender or a bender kit is more economical than buying individual tools.